FrSky Tarainis and RX Parts

This week we received a shipment of parts and accessories from FrSky. Many of our customers were asking for replacement parts for broken switches, knobs, antennas, etc. To accommodate their request and to stock replacement parts for the FrSky Taranis as well as several of their receivers, we brought in a selection of antennas, antenna cables, switches, knobs, gimbals.

Our clients which do not have the luxury of running an FrSky Taranis, but would like to benefit from the advantages of the two way radio systems might choose to use one of the 3 available FrSky modules which will make their radio compatible with FrSky protocol and telemetry system. The 3 available modules are pictured below:

FrSky DJT ModuleFrSky DFT ModuleFrSky XJT module

The above modules can be used in one of the following transmitters:

  • DJT: JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, MX-22, MX-24S, PX, 9XII, Turnigy 9x/FlySky 9x/EMAX 9x
  • DFT: Futaba: 3PM, 3PK, 7U, 8U, 8J, 9C, 9Z, 10C, FN series, T10C, FC-18, FC-28, Hitec: Optic 6, Eclipse 7, Prism 7, WFLY: WFT09, WFT08
  • XJT: JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, MX-22, MX-24S, PX, 9XII, Eurgle 9X, Turnigy 9X and more.

In case you already have the FrSky Taranis radio and some switches, sliders, knobs are broken, you choose to replacement your switch with ine of the following ones:

Replacement Gimbal. Use this to replace your broken or defective gimbal.FrSky Gimbal
A pair od sliders. Use this to replace your broken sliders on the left and right side of your Taranis.FrSky Taranis Sliders
This one position switch is usually used as a trainer switch. It is a momentary switch and it goes back to the default position when it is released. Use this to replace the SH switch on your Taranis.One Position Switch
This long lever 2 position switch is the only 2 position switch on the Taranis. Replace your SF switch with this.2 position switch
This is a 3 p[osition short lever switch for replacement of the SA, SD, SE or SG switches.IMG_9167
3 position long lever switch to replace the SB or SC switches on your Taranis.3 Position Long Lever
This 6 position switch can replacea nby of your switches and give you a fixed 6 position choice. Good for those flying a Pixhawk or APM.IMG_9152

In case you need assistance with any of these repairs of replacements, or if you do not feel up to it, please call us at 416 642-6830 and we can do the repairs for you.

We also received several types of antennas these can be used as a replacement for your current FrSky receivers, or as a new antenna for a bit different purpose. Each of these antennas are used in different scenarios, so please check the list below for availabilities:

 

This is a replacement antenna for the FrSky Taranis. This 7db patch, according to some sources will increase the range of the radio 3 times - but I would be very cautious with that statement. For sure you have to point it to the correct direction as this is a directional antenna and that will give you increased range compared to the original 3bd tilt-swivel rubber duck.FrSky 7DB TX Antenna
This 150mm wire antenna is a direct replacement for receivers like D4RII and similar.FrSky 150mm RX Antenna
The 250mm Antenna really is a longer feedline antenna to allow you to position the antenna further out from your receiver. You can place the receiver inside the model and move the antenna out on the wing for better reception.FrSky 250mm RX Antenna
Just like the 250mm antenna, the 400mm antenna allows you to move the active antenna (Heat-shrinked black part) further out from the inside allowing it to be used in larger models.FrSky 400mm RX Antenna
The 600mm feedline antenna is for large scale models to move the antenna out to the wing or back side of the model allowing better signal selectivity.FrSky 600mm RX Antenna